A Tokyo-based app engineer has Doom running on a 486 DX2 PC built on a breadboard. The shortcut is an FPGA board that handles the chipset's work. According to Tom's Hardware, the whole build appears to have taken just 16 days. That count starts on 24 October, when the CPU first appeared in the developer's posts, and ends on 9 November, when a Doom video went up.
The project comes from the X user @nagakurage. Tom's Hardware news editor Mark Tyson reported on the build. We couldn't check the developer's original posts directly, so everything below is as Tom's Hardware reports it, including the one post it embeds.
The shortcut hiding in plain sight
This is where the build gets clever. On a normal 486 motherboard, the chipset is the support logic that links the CPU to memory, storage and everything else. An FPGA is a chip whose logic can be reconfigured after it's made. According to Tom's Hardware, the developer bought a Colorlight i9 v7.2 FPGA board to attach the CPU to and "to cover chipset duties."
So the 486 is real silicon, and reprogrammable hardware does the chipset's job. The CPU end of the wiring is still hardcore. Tom's Hardware says every pin of the CPU appears to have been connected separately to an experimental "socket" made from a baseboard. Its aside on that socket: "We know this is a breadboard PC, but there are limits…"
The socket shows up from day one. The 24 October post that Tom's Hardware embeds reads "i486 CPU実験用ソケット完成 低クロックで動かなければ基盤発注する". Our rough translation: the experimental i486 socket is finished, and if it won't run at a low clock speed, a proper board gets ordered.
The chip
Tom's Hardware says the CPU was the sought-after DX2 66 model, which runs at 66 MHz internally and 33 MHz externally thanks to a 2x clock multiplier. It describes a gray made-in-Malaysia chip with 168 pins on the underside. That multiplier is what made the DX2 such a big deal back in the day: the core ran faster while the rest of the motherboard stayed at bus speed.
Sixteen days, step by step
Here's the timeline as Tom's Hardware lays it out:
- 24 October: the i486 DX2 66 shows up on @nagakurage's timeline.
- 26 October: the finished breadboard system starts to take shape, and the CPU blinks an LED using x86 code.
- 31 October: RAM goes in and gets tweaked until it runs error-free.
- 3 November: microSD storage is added, and the same day the machine boots FreeDOS 1.3 for the first time. Tom's Hardware notes it used a machine translation for this part.
- 9 November: a video demo of Doom running on the finished machine is published.
By Tom's Hardware's count, that's 16 days from the first CPU post to the Doom video. Most of us take longer than that to get a cable-managed case looking tidy.
The monitor is a tiny fake CRT
The machine also needed a screen. Tom's Hardware says the developer printed the parts for a CRT-style enclosure on a Bambu Lab A1 mini. Tom's Hardware also says the case was designed by Claude, Anthropic's AI assistant. Inside it sits a 5-inch 800×480 Elecrow Raspberry Pi panel. On 9 November the beige-shelled monitor and the breadboard PC were shown side by side and powered up. According to Tom's Hardware, Doom "looked smooth enough on the vintage 1992 silicon, as it should do."
That fits. Doom launched in December 1993, when 486s were mainstream.
Next stop: PC-98
The project isn't finished. Tom's Hardware reports that the developer wants to refine the build and make it fully PC-98 compatible. NEC's PC-9800 series was the dominant PC platform in Japan in the early 90s, and it ran its own software library, separate from the IBM-compatible PCs the rest of the world used.
It isn't the first build like this, either. Tom's Hardware notes that in April it covered another enthusiast's breadboard-based Intel 386 system.
Jax's take: I reckon the FPGA is the smartest call in this build. Letting reprogrammable hardware cover the chipset probably helped keep the timeline short, though only the developer knows how much. Knowing which job to hand off to reconfigurable logic is half the engineering.
Reporting notes



